|
|
51-1000 ALIGNMENT TELESCOPE An
economical and accurate optical alignment instrument well-suited to applications not
requiring a micrometer. Magnification 34x at infinity. All W-K alignment telescopes are
made of heavy walled, heat treated, alloy steel tubing meeting AIA specifications.
Illumination is available by low voltage transformer and bulb. |
|
51-2000 SPHERICAL ALIGNMENT TELESCOPE W-K's Line of sight telescope for spherical alignment systems meeting AIA
specifications without micrometers. Magnification to 34x. Telescope 17.75 inches. Diameter
2.2495 to 2.2498 inches. Illumination and case. |
|
51-2200 SPHERICAL MICROMETER ALIGNMENT TELESCOPE W-K's most versatile alignment scope with two micrometers for precise
measurements in two directions perpendicular to the line of sight. Magnification increases
to 34x at infinity focus. Micrometers Range .100 inch. Graduation 0.001 inch. Accuracy
0.0001 inch. Barrel length 10 inches. Overall length 17.75 inches. Diameter 2.2495 to
2.2498. Illumination and case. |
|
|
51-3000 ALIGNMENT COLLIMATOR Used to establish positions in reference to a line of sight and for checking and
adjusting optical alignment instruments. The collimator barrel is machined from hardened
steel with a hard chrome surface. Barrel length is 12 inches, diameter is 2.2498 inches.
The infinity target is graduated every 30 seconds. |
|
|
We recognize the quality of the WIld and Kern Theodolites and
specialize in the support the these instruments and their accessories including
autocollimation eyepieces, optical micrometers, short focus lenses. These instruments are
factory reconditioned and certified to operate to the manufacturers original
specifications. |
|
|
The Wilt T2 Universal Theodolite. In addition to its high accuracy,
it is simple to handle and has many accessories. An inverter knob brings the required
circle image in to the reading eyepiece. The horizontal circle appears yellow, the
vertical white. Coincidence setting for direct reading of the mean of two diametrically
opposite circle positions. Automatic index for vertical circle. The all-steel T2 is a
truly universal theodolite for optical tooling. |
|
|
Wild T2000. The system fulfils a long-awaited requirement. As the
graduations around the whole circle are scanned for every reading, circlegraduation errors
cannot occur. Scanning at diametrically opposite positions eliminates the influence of
eccentricity. The standard deviation of the mean of a face left and a face right pointing
is 0.5” for both the hozizontal and vertical circles. The T2000 has a circular bubble
and a plate level. |
|
|
Kern DKM2-AT. The outstanding universal theodolite with high
measruing accuracy, yet simple operation. The digital readout direct to 1 second virtually
eliminates reading errors. Steel construction for maximum stability and precision.
Maintenance-free compensator for vertical indexing. Coarse and fine orientation-drive to
accurately set hoizontal circle. |
|
|
OPTICAL MICROMETERS These micrometers measure horizontal or vertical line displacement. They have
a range of .200 inch. Micrometer Scales read to .001 inch. Unit has a dust cover glass and
a split clamp for mounting on telescopes.
58-2100 Single axis Optical Micrometer
58-2200 Dual Axis Optical Micrometer |
|
|
AUTOCOLLIMATION EYEPIECE This
eyepiece converts most auto-levels and theodolites to autocollimation instruments.
Illumination of reticule is provided by a 4D cell battery pack. Autocollimation eyepieces
are available for many instruments. Contact us with your individual requirements. |
|
|
51-9005 SPHERICAL ADAPTER This
adapter is a hardened steel sphere ground to 3.500 inch diameter. It has a collet for
clamping the adapter on any point along the barrel of a telescope, collimator, or tube
2.25 inch in diameter. |
|
|
51-9010 WYE ROTATING BASE A
precision mounting base designed to accommodate all 2.25 alignment telescopes and
collimators. Four screw leveling and slow motion tangent screw make positioning reliable
and easy. |
|
|
SLIDES W-K slides
are 3-1/2 inch x 8 thread. Compatible for use with any brackets, stands or tripods.
5/8"x11 thread adapters available.
59-1350 Precision Lateral Slide
59-1361 Single Axis Micro Slide..with 001 micrometer
59-1362 Dual Axis Micro Slide...with X+Y.001 micrometer |
|
|
51-9020 TILT MOUNTING BASE This
mounting base accommodates all alignment telescopes and collimators in vees with 9.5
centers. 3-1/2"x 8 thread mounting base. Fine adjustment for horizontal and vertical
control by large adjusting screws for easy adjustment. |
|
|
58-1890 MAGNETIC MIRROR A
mirror used to check the perpendicularity of any flat surface to a line of sight by means
of auto-reflection or auto-collimation. 2.5 inch diameter. 1/4 wave length in 50mm flat.
Single magnet parallel to within 3 arc seconds. |
|
|
STAND EXTENSIONS Extension
piece increases the maximum height of W-K tripods and stands. Fitted with a 3-1/2"x8
male and female thread. Hollow for vertical centerline plumbing.
59-3505 5 inch
59-3510 10 inch
59-3520 20 inch |
|
|
51-9090 ELECTRONIC STRIDING LEVEL/ELT The ESLT uses electronic level sensing to give sub arc second
accuracy to telescopes and collimators. Housing can be dismounted from striding bracket to
function as an electronic level for plates and other surfaces requiring very accurate
monitoring. |
|
|
51-9030 OPTICAL SQUARE The optical square is mounted on an alignment telescope or an alignment
collimator with a diameter of 2.2498 inch. It is generally used to establish a plane
perpendicular to the telescope line of sight. 90 degrees to within one arc second. The
optical system is mounted in a spherical housing of 3.500 in diameter. |
|
|
SCALE HOLDERS 58-1100
Magnetic Scale Holder.. Holds 3, 5, 10, 20 inch scales.
58-1106 Scale Level...Levels optical tooling scales either vertical or horizontal.
58-1150 V-Block Scale Holder... Assures positive contact with shaft. |
|
|
AUTO REFLECTION TARGETS 58-1800
Glass Target
58-1810 Mounted Target
58-1820 Small Glass Target
58-1830 Small Mounted Target
58-1840 Mirror Target
58-1850 Plastic Target
58-1860 Adhesive Target |
|
|
INSTRUMENT STANDS In
addition to a wide selection of standard stands, W-K custom manufactures many variations
for specific setup requirements. We will quote your specific requirements. |
|
|
59-2000 STATIONARY ADJUSTABLE STAND W-K's adjustable fixed stand for inside and outdoor use. 3-1/2"x 8
thread. MOVEABLE STAND...Provides rigid support for optical alignment and are easily
positioned by rolling on retractable casters. Adjusting bolts permit leveling of stand.
59-2000
Stationary Adjustable Stand
59-2310 Low Moveable Stand 24" to 41"
59-2320 High Moveable Stand 40" to 73" |
|
|
59-3000 TRIVET For
supporting jig transit or theodolite. Very rigid and is supported by removable, hardened
steel points. 3-1/2"x8 mounting thread. 5-5/8" height. |
|
|
SCALES Easy to
read optical tooling scales allow precise dimensional measurements accurate to 0.001 of an
inch.
58-1003 3 inch
58-1005 5 inch
58-1010 10 inch
58-1020 20 inch |
|
|
51-9040 STRIDING LEVEL This level is used for establishing a level line of sight on any alignment
telescope or alignment collimator with a 2.25 inch diameter.
51-9045 COINCIDENCE STRIDING LEVEL
A Striding Level that uses a coincidence type level with
magnification permitting leveling to within 1 arc second. |
